Innotech Genesis II Digital Controller (v5) Instrukcja Użytkownika Pobierz pdf (Strona 55)

Page 55

Genesis II Installation Instructions

The RS485 Comms connection block is in the upper right section of the module and the End of Cable

Jumper is next to it.

Digital Input terminals are located at the bottom of the module; input signal connections are listed in

Table 3-15.

Terminal Signal

A DI 1+

B DI 2+

C DI 3+

D DI 4+

E DI 5+

F DI 6+

G DI 7+

H DI 8+

I Common

J Common

Table 3-15: GENII DI REM Digital Input Signal Conditions

1 2 ... 50 51 52 53 54 55 56 57 58 59 60 ... 123 124

INSTALLATION INSTRUCTIONS 1
Proprietary 2
Trademark 2
Disclaimer 2
Document Management 3
Document Title: 3
Revision History 3
Contents 5
Contents (Continued) 6
List of Illustrations 8
List of Tables 10
Chapter 1 - Preliminary 11
Information 11
1-1 Introduction 12
Table 1-1: Document Chapters 13
1-2 Special Considerations 14
1-3 Unpacking Instructions 14
1-4 Installation Plans 14
1-5 Tools and Test Equipment 14
Chapter 2 - Mechanical 15
2-1 Introduction 16
2-2 Physical Descriptions 16
Mounting Hole 17
Typical of 8 17
GENESIS MPC 19
GENESI S 20
ANALOG INPUT 20
DO 1 DO 2 DO 3 23
MOUNTING 25
2-3.1 DIN Rails 26
Side View 28
Top View 28
90 Degrees 28
2-4 Dierence Data 29
Chapter 3 - Electrical 31
3-1 Introduction 32
3-4.1 REM Power Connections 50
3-4.2 REM Comms Connections 51
DIGI TA L OUTPUT 56
Remote Expansion Modul e 56
ISOLA TED DIGI TA LINPUT 57
PULSE INPUT 58
24V AC or DC Supply 64
0V AC or DC Supply 64
C ON TROL S YSTEMS 66
USTRALIA 66
Chapter 4 75
Commissioning 75
4-1 Introduction 76
JUMPER WIRE 81
SWITCH CLOSED 83
SWITCH OPEN 83
GENII DI REM 83
EXTERNAL 85
GENESIS II DDCINNOTECH 87
4-1.3 Install AISCs 90
4-1.4 Set Jumper Plugs 91
AI 5 A I6 AI7 AI8 AI 9 92
RS485 COMMS 93
CONNECTIONS 93
END-OF-CABLE 93
GEINNOTECH 94
4-1.6 Initial Tests 97
4-1.7 Final System Check 99
Chapter 5 - Network 101
Installation 101
5-1 Overview 102
5-2 Genesis II Products 102
5-2.1 Definitions 103
5-3 Installation 104
5-3.3 Wiring Topology 105
Zone A Zone B 107
Zone BZone A 107
Repeater 108
Page 109 109
- - - - 111
Page 113 113
Building A 115
Building B 115
DANGEROUS EARTH CONNECTION! 117
NOT TO BE USED! 117
Page 119 119
Page 121 121
MPI With Isolated RS485 122
Isolated from 123
Connected to 123
Innotech Support 124

Komentarze do niniejszej Instrukcji

Brak uwag

Innotech Genesis II Digital Controller (v5) Instrukcja Użytkownika Strona 55

Komentarze do niniejszej Instrukcji