Innotech Genesis V4 System Instrukcja Użytkownika Strona 9
- Strona / 115
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Installation Instructions for Innotech Genesis Systems
Edition: 011100
v
LIST OF ILLUSTRATIONS – (Continued)
FIGURE PAGE
4-1. Checking Power Input. ...............................................................................................4-4
4-2. Checking Digital Input Wiring. .................................................................................4-6
4-3. Checking Dry Contact Inputs. ....................................................................................4-8
4-4. Checking Digital Output Wiring. ...............................................................................4-10
4-5. AISC Locations. .........................................................................................................4-12
4-6. Address Jumpers, Typical Settings. ...........................................................................4-20
4-7. End-of-Cable Jumper, Typical Location. ...................................................................4-20
4-8. Setting Analogue Output Jumpers. ............................................................................4-21
A-1. Correct and Incorrect Bus Topology. .........................................................................A-3
A-2. Adding Modules to a Network. ..................................................................................A-3
A-3. Linking Networks in Different Locations. .................................................................A-4
A-4. Multi-Network Arrangement. ....................................................................................A-4
A-5. Network Nodes Considerations. ................................................................................A-5
A-6. Genesis Comms Wiring Connections. .......................................................................A-6
A-7. Genesis I Connections. ...............................................................................................A-7
A-8. Genesis II Connections. .............................................................................................A-8
A-9. Genesis II POLY SWITCH Board. ............................................................................A-9
A-10. GENII 485I Isolated RS485 Comms Card. ................................................................A-10
A-11. GENII RPTR Repeater Module Connections. ...........................................................A-11
A-12. GENII MPI Modem and Printer Interface. .................................................................A-13
A-13. Genesis I Non-Isolated Comms. ................................................................................A-14
A-14. Genesis II Non-Isolated Comms. ...............................................................................A-15
A-15. Hazardous Connection Example, Circuit 1. ...............................................................A-16
A-16. Hazardous Connection Example, Circuit 2. ...............................................................A-17
A-17. Use of GENII Poly Switch Boards, Circuit 1. ...........................................................A-18
A-18. Use of GENII Poly Switch Boards, Circuit 2 ..............................................................A-19
A-19. Use of GENII 485I Card, Circuit 1. ...........................................................................A-20
A-20. Use of GENII 485I Card, Circuit 2. ...........................................................................A-21
A-21. Use of GENII RPTR Repeater Module, Circuit 1. ....................................................A-22
A-22. Use of GENII RPTR Repeater Module, Circuit 2. ....................................................A-23
A-23. Use of GENII MPI, Circuit 1. ....................................................................................A-24
A-24. Use of GENII MPI, Circuit 2. ....................................................................................A-25
A-25. Voltage Check, Isolated/Non-Isolated Digital Controller. .........................................A-26
A-26. Voltage Check, GENII MPI with Isolated/Non-Isolated RS485. ..............................A-27
A-27. Voltage Check, GENII RPTR Repeater Module. ......................................................A-27
- Innotech 1
- PROPRIETARY 3
- TRADEMARK 3
- TABLE OF CONTENTS 5
- LIST OF ILLUSTRATIONS 8
- LIST OF TABLES 10
- GENESIS II 18
- DIGITAL INPUT MODULE 18
- GEN II AI REM 19
- REMOTE MODULE INTERFACE 20
- D.I.M. D.I.M. D.O.M. D.O.M 22
- SIDE VIEW TOP VIEW 23
- 90 DEGREES 23
- GENESIS II DDCINNOTECH 29
- GEN II MPC 36
- ANALOGUE INPUT MODULE 41
- 3233 343536 42
- DIGITAL OUTPUT MODULE 44
- ++ = Positive Comms Line 46
- −− = Negative Comms Line 46
- A1 A2 A3 A4 A5 A6 48
- ABCDEFGH I J 50
- DI 1 DI 2 DI 3 DI 4 DI 5 53
- • C+ = RS 485 (+) Signal 54
- • C- = RS 485 (-) Signal 54
- • SHLD = Comms cable shield 54
- COMMS DIGITAL INPUTS SENSOR 55
- COMMISSIONING 56
- 4-1.2.2 60
- 4-1.2.2.1 60
- JUMPER WIRE 61
- 4-1.2.2.2 62
- SWITCH CLOSED 63
- SWITCH OPEN 63
- GENII DI REM 63
- 4-1.2.3 64
- EXTERNAL 65
- 4-1.2.4 67
- ANALOGUE 69
- CONDITIONERS 69
- 4-1.2.4.2 70
- 4-1.2.4.3 72
- 4-1.2.5 72
- 4-1.4.1 74
- 4-1.4.2 74
- 4-1.4.3 75
- INNOTECH 76
- 4-1.7.1 78
- 4-1.7.2 79
- 4-1.7.2.1 79
- Example A 84
- Example B 84
- Zone A Zone B 85
- Zone BZone A 85
- 1234- - - 29 30 31 32 86
- 1 234- - - 29 30 31 32 86
- 1 234- - - -29 30 31 32 86
- Pin Strip 90
- BOTTOM EDGE OF BOTTOM BOARD 90
- Screen1 2 100
- Isolated 101
- 89 90 91 92 93 107
- MPI With Isolated RS485 108
- Comms Cables for Port 2 108
- Comms Cables for Port 1 108
- Edition 011100 109
- APPENDIX B- DATA SHEETS 110
Powiązane produkty i podręczniki dla Oprogramowanie Innotech Genesis V4 System
(44 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji